Install the following components using organic solder. Remember to wash the boards off.
Insert the following resistors:
271-100K (32) (Note on R70: This gives the breakpoint a 10
volt range. To give it a 5 volt range that is more compatible
with MOTM systems, make this a 49.9K resistor.)
R1,R10,R12,R15,R16,R17,R18,R19,R20,R21,R22,R23,R24,R25,R26,R39,R40,R41,R42,R43,R44,R45,R46,R47,R48,R49,R50,R70,R74,R75,R78,R79
271-30K (1) (Note: This gives the breakpoint a 10 volt range.
To give it a 5 volt range that is more compatible with MOTM systems,
make this a 10K resistor.)
R67
271-49.9K (1)
R7 (R2,R3,R9&R11 will be installed later)
271-24.9K (1)
R69
271-1K (3)
R8,R64,R72 (4 more 1K resistors will be installed later: R2',R3',R9',R11')
271-10 (2)
R66,R71
271-10K (2)
R63,R68
271-200K (2)
R5,R73
-----START, OUT+ and OUT- resistor installation -----
271-49.9K (4) (Note: these do not install directly in their
position, but instead install just one lead, with the other lead
connected to a wire for the individual stage outputs. The lead
goes into the hole nearest U2. The "open" lead where
the wire is to be installed should be oriented to the right so
the designated wire lengths will reach them.)
R2,R3,R9,R11
271-1K (4)
R2',R3',R9',R11' (Note: these install with one leg in the R2,R3,R9&R11
positions, and the other leg attached to a wire that goes to the
individual stage outputs. These install into the R2, R3, R9 or
R11 hole farthest away from U2. The "open" lead should
be oriented to the right so that the designated wire lengths will
reach them.)
-----END-----
Insert the following diodes:
78-1N914 (14)
D1,D2,D3,D4,D9,D10,D11,D12,D17,D18,D19,D20,D22,D23 (Be careful
when installing as the polarities are not always the same. An
easy check is that all pairs criss-cross except pairs D19&D20
and D22&D23. The line for the diode cathode is superimposed
on the "N" in 1N914.)
610-1N751A (1)
D21
Insert the following capacitors:
140-XRL25V10 (2)
C1,C2 (long lead to "+" hole)
80-C410C104M5U (14)
C3,C4,C5,C6,C7,C8,C9,C10,C11,C12,C13,C14,C15,C16,C17,C18,C19,C20,C21,
C22,C23,C24 (Note to self: C17,C18,C6&C4 not required because
U5 and U6 are not populated. C9,C11,C16&C19 are not required
because U9 and U10 are not populated.)
Insert the following integrated circuits:
511-TL071CN (1)
U1
511-TL072CN (6)
U2,U3,U4,U7,U8,U11
511-LM336Z (1)
U12 (looks like a transistor)
Insert the following transistors:
625-2N3904 (2)
Q1,Q2
625-2N3906 (2)
Q4,Q3
Solder the following with no-clean solder:
571-6404454 (1)
P5 (no orientation on PCB, the flat retainer clip goes towards
the outside PCB edge.
72-T20YP-20K (1)
R65